We have included a starting point for application of fabric, vinyl, spangles and rhinestones. Because iron temperatures, hand pressure and ironing surfaces vary you may need to adjust your application method for your equipment. Below are starting points. Adjust as necessary.
IMPORTANT INFORMATION REGARDING RIBBON WIDTH AND YARDAGE: Ribbon widths may vary. This is a normal part of the manufacturing process called variance. This happens with ALL ribbon manufacturers, colors, widths, etc. We work closely with our manufacturer to minimize this, but it can happen. This can cause a 3" wide ribbon to be slightly less or slightly more than 3" wide (it actually happens with all widths, but is most noticable in wider widths). We trim and size all our fabric, vinyl, spangles and rhinestones to fit 3" ribbon ALMOST every time. Most widths are cut to 2.8" wide for vinyl, spangles and rhinestones and a full 3" for fabric. There will be times when some modification will be necessary to achieve the desired look (such as removing some rhinestones, trimming an edge of fabric, centering the fabric on your ribbon without edge to edge coverage, etc.). The only way to fully prevent this is to first measure the exact piece of ribbon you intend to use (for each bow because even in a continuous spool of ribbon, the width can vary) and then custom cut each piece for that one bow. Please rest assured that the vast majority of our products work seemlessly together and can easily be worked with.
Ribbon spools greater than 5-yards long may not be continuous. We avoid splices in the ribbon as much as possible, but it is a normal manufacturing expectation.
BEFORE YOU BEGIN:
We carefully inspect all materials before leaving our warehouse, but there may be occasions when a piece of vinyl has been left unweeded, a rhinestone may be missing or shifted out of place or a spangle dot could be mis-cut. Please inspect before applying to make sure that no adjustments are needed. We have designed our strips so that if a spangle or rhinestone is out of place/missing you can easily adjust stones or spangles. The transfer tape is sticky. Just pick up a stone and press it down where you'd like on the tape (upside down). Spangles can be adjusted with tweezers or a pin.
- Set the heat press to 280-290 degrees Fahrenheit or medium/high if using an iron.- Set the timer to 10 seconds.- Adjust the upper platform so the pressure is high, but still able to lock down.- Pre-press your ribbon to flatten out any wrinkles, then allow it to cool a little bit.- Remove white backing sheet from spangle design (all you should have is the clear plastic and the spangle design) Place spangle design sticky side down aligned on your ribbon. There is no need for a cover sheet, but you may use a non-stick cover sheet or pillow case if you choose to.- Lower heat-press. If you are using an iron, use a flat surface and firm pressure and press in sections (sligtly overlapping) until entire transfer is applied.- Once finished, remove garment and lay out flat, design downward, on your work table.- Rub the backside of the design to assist in cooling.- Turn it over and rub design firmly with another garment or even the sleeve of this one.- Once the design cools, peel off transfer paper in the direction that stretches the garment the least.- Press a second time for half the original time frame. This helps to lock down the spangles.If any spangles come off during this peel, you can cut out the transfer paper that holds the spangle dot(s) and replace it where it belongs. Your cut out does not have to be too precise as to hold just the one little dot(s), it should be of a workable size. Reheat the whole design for just 5-6 seconds. Press the dot(s) firmly. Be careful not to move any of the others spangles since they will be vulnerable to movement. Allow the ‘dot’ to cool then carefully peel off the transfer paper cut out. This second pressing will serve as the second press for the whole design.
Spangles should be applied to ribbon or smooth fabric only (such as regular mystique). They will not permanently adhere on top of any type of vinyl (no glitter or holographic at all). It will appear that the spangles are adhered, but they WILL eventually fall off if placed on top of glitter.
- Set the heat press to 345 degrees Fahrenheit or high/cotton/linen setting if using an iron. Traditionally it is not recommended to press rhinestones on top of glitter vinyl and we do not recommend attempting it with a hand iron. However, since bows are not washed like garments are, you may be able to apply rhinestones on top of the glitter vinyl successfully. You must have a heat press with verified temperature and heavy pressure for this to work. The most permanent and professional application is to place rhinestones on top of fabric or ribbon.
- Set the timer to 10 -15 seconds. Designs with SS16 or larger stones will need to be pressed on a heat press only, heavy pressure and 20-30 seconds. Please make sure all materials you are pressing are compatible with the pressing specs for proper rhinestone adhesion. Not following these instructions will resutlt in rhinestones falling off.- Adjust the upper platform so the pressure is high, but still able to lock down.- Pre-press your ribbon to flatten out any wrinkles, then allow it to cool a little bit.- Remove white backing sheet from rhinestone design (all you should have is
the clear plastic and the rhinestone design) Place rhinestone design sticky
side down aligned on your ribbon. There is no need for a cover sheet, but you may use a non-stick cover sheet or pillow case if you choose to.- Lower heat-press. If you are using an iron, use a flat surface and very firm pressure and press in sections (slightly overlapping) until entire transfer is applied.- Once finished, remove ribbon and lay out flat, design downward, on your work table.- Once the design cools, peel off transfer paper in the direction that stretches the garment the least.- If any rhinestones lift, place back down and press again.
If using both rhinestones AND spangles on the same ribbon, apply the spangles first and then adhere the rhinestones. If you apply the rhinestones first, the dimension of the rhinestones will not allow enough pressure for spangles to adhere, too.
Heat Transfer Vinyl (Glitter, Holographic, Flock, Standard Finish, Metallic):
Our vinyl is cut with the carrier sheet intact. This means that you can also cut it on your vinyl cutter if you choose to. Just remember to cut a mirror image.
Glitter Vinyl: Blade Setting 5; Speed 5; Thickness 10.
To adhere to ribbon
- Set the heat press to 330-340 degrees Fahrenheit or high/cotton/linen setting if using an iron.- Set the timer to 10 -15 seconds.- Adjust the upper platform so the pressure is high, but still able to lock down.- Pre-press your ribbon to flatten out any wrinkles, then allow it to cool a little bit.- Place design aligned on your ribbon. There is no need for a cover sheet, but you may use a non-stick cover sheet or pillow case if you choose to.- Lower heat-press. If you are using an iron, use a flat surface and very firm pressure and press in sections (sligtly overlapping) until entire transfer is applied.- Once finished, remove ribbon and lay out flat, design downward, on your work table.- Remove the clear carrier sheet from the vinyl. Temperature is important -Glitter - warm peel; holographic - cold peel; Flock - cold peel; standard - warm or cold; metallic - cold peel.
**Important - DO NOT OVERHEAT your fabric strips. This will cause the glue to deactivate and they will not adhere properly. More heat will not give you a better adhesion. It is actually just the opposite. Use a household iron only. If you need to heat multiple times (to layer or add decals, spangles, etc., try to iron them onto the fabric strips BEFORE you remove the paper to avoid ruining the glue, if possible). Or if adding something dimensional such as rhinestones, iron the fabric strip down with an extremely light initial press to "tack" the fabric strip down in place so it won't move on it's own, but is easily peeled off. Then add your rhinestones on top and do a quick final press from the back. This will help prevent overheating.
- Heat n bond is already applied to the back of your fabric strip. We lightly apply just in case you need to do a multi-layer application requiring you to heat the fabric strip multiple times. (adding spangles or rhinestones on top). If the heat n bond is separating, just lightly iron the paper side of the fabric strip. It will stick right back on.- Peel off paper liner.- Place material, adhesive side down, on top of your ribbon. Press & hold iron (use household iron ONLY - we do not recommend a heat press) for 4-8 seconds on each section until entire entire piece is bonded.
If you do happen to overheat and deactive your glue, don't worry. You probably have not ruined the strip. All that is needed is another layer of heat n bond on the back. Since it is already cut to size, cut a piece of heat n bond material slightly bigger than the strip. There is no need to be exact, you can use just scissors. Iron the strip onto this piece from the back (paper side). Allow to cool and peel the fabric off the heat n bond. The glue will stick to only the fabric strip and you can start over. It's okay! It happens to everyone at some point.
Ready to press sublimation sheets: YOU MUST HAVE A HEAT PRESS CAPABLE OF REACHING 400 DEGREES. A HOUSEHOLD IRON WILL NOT WORK
On glitter HTV:
Directly on ribbon: (must be 100% polyester ribbon.
Fabric: (must be 100% polyester fabric)
If applying multi-layers - follow this order:
1. Fabric strip or vinyl to ribbon
2. Apply spangles to fabric
3. Apply rhinestones
Sometimes, heating fabric multiple times for multi-layer applications can cause adhesion problems. Heat and bond glue tends to soak too much into fabric or burn off if it is overheated and will start to separate. If this happens, try these tips:
- apply spangle or rhinestone strips to fabric strip first before applying the fabric to the ribbon. Just leave the paper back in place and press the spangles right on top using the above instructions. Then, peel off the paper and apply the fabric with the spangles or rhinestones to the ribbon like normal. This allows multiple heatings without the glue soaking into the ribbon AND fabric at the same time. Keeping the paper intact seems to keep the glue from burning off/soaking in too much.
- when layering vinyl (especially cut out layers) do a half press to adhere the first layer and subsequent layers. You want to pressed just enough so it sticks, but not a final press. Once all layers are in place, do a final press for 5-6 seconds.
-You should avoid layering glitter vinyl. You can get away with it somewhat for cheer bows, but because of the texture, it will eventually separate. You cannot layer anything over holographic vinyl. It is too slick of a surface and anything will peel right off.